1. Which security protocol or measure would provide the
greatest protection for a wireless LAN?
WPA2
cloaking SSIDs
shared WEP key
MAC address filtering
2.Refer to the exhibit. All trunk links are operational and
all VLANs are allowed on all trunk links. An ARP request is sent by computer 5.
Which device or devices will receive this message?
only computer 4
computer 3 and RTR-A
computer 4 and RTR-A
computer 1, computer 2, computer 4, and RTR-A
computer 1, computer 2, computer 3, computer 4, and RTR-A
all of the computers and the router
3.Refer to the exhibit. Hosts A and B, connected to hub HB1,
attempt to transmit a frame at the same time but a collision occurs. Which
hosts will receive the collision jamming signal?
only hosts A and B
only hosts A, B, and C
only hosts A, B, C, and D
only hosts A, B, C, and E
4.Refer to the exhibit. Router RA receives a packet with a
source address of 192.168.1.65 and a destination address of 192.168.1.161. What
will the router do with this packet?
The router will drop the packet.
The router will forward the packet out interface FastEthernet
0/1.1.
The router will forward the packet out interface
FastEthernet 0/1.2.
The router will forward the packet out interface
FastEthernet 0/1.3.
The router will forward the packet out interface
FastEthernet 0/1.2 and interface FastEthernet 0/1.3.
5.Refer to the exhibit. Which two settings show the default
value of VTP configuration on a Cisco 2960 switch? (Choose two.)
revision number
existing VLANs
operating mode
domain name
pruning mode
6. Which value determines if a switch becomes the central
point of reference in the spanning tree topology?
lowest bridge ID
highest revision number
lowest numeric IP address
highest numeric MAC address
7. What is the purpose of the Spanning Tree algorithm?
It propagates VLAN configurations to other switches.
It restricts broadcast packets to a single VLAN.
It segments a network into multiple broadcast domains.
It prevents loops in a switched network with redundant
paths.
8. What are two benefits of the IEEE 802.11n standard over
the IEEE 802.11G? (Choose two.)
requires less equipment
provides improved range
permits increased data rates
has a single-input and a single-output
needs no hardware upgrade for compatibility
9. Which configuration changes will increment
the configuration revision number on the VTP server?
configuring trunk links on the VTP server
configuring or changing the VTP password
configuring or changing the VTP domain name
configuring or changing the VTP version number
configuring or deleting a VLAN or creating a VLAN name
10.Refer to the exhibit. A company has acquired a new office
in a campus environment. Switches in the existing office and the new office are
directly connected by a trunk link. The VLANs and IP addressing are setup as
shown in the exhibit. The computers in each office are not able to ping each
other. What will fix the problem?
Use an access link between S2 and S3.
Connect S2 and S3 to a common router.
Set the subnet mask in the new office to /24.
Configure the new office default gateway to 172.17.10.1
Change the port assignments in the new office to a
different VLAN.
11. What is a possible impact of setting too short an aging
time in the MAC address table of a switch?
overly large address table
unnecessary flooding of packets
excessive timeouts of static addresses
impaired ability to dynamically learn new addresses
12.Refer to the exhibit. The network administrator has just
added VLAN 50 to Switch1 and Switch2. Hosts A, B, C, and D are correctly
configured with IP addresses in the subnet range for VLAN 50. Host A can
communicate with host B, but cannot communicate with host C or host D. What is
the cause of this problem?
There is a native VLAN mismatch.
The Fa0/11 interface of Switch1 is not configured as a
trunk.
The link between Switch1 and Switch2 is up but not trunked.
VLAN 50 is not allowed on the trunk link between Switch1
and Switch2.
13.Refer to the exhibit. Users complain that they do not have
connectivity to the web server that is connected to SW1. What should be done to
remedy the problem?
Allow all VLANs on the trunk link.
Configure VLAN 100 as the native VLAN for SW1.
Configure the trunk port in trunk mode on SW1.
Attach the web server to a router and configure inter-VLAN
routing.
14. What VLANs are allowed across a trunk when the range of
allowed VLANs is set to the default value?
only the management VLAN
all VLANs except the extended range VLANs
all VLANs except 1 and 1002-1005
all VLANs
15.
Refer to the exhibit. A new host needs to be connected to VLAN 1. Which IP address should be assigned to this new host?
192.168.1.11 /28
192.168.1.22 /28
192.168.1.33 /28
192.168.1.44 /28
192.168.1.55 /28
16. Using the command copy tftp:backup.cfg startup-config,
an administrator downloaded a saved configuration from a TFTP server to a
switch. Why does the administrator not detect any changes in the switch
configuration after the download completes?
The command should have been copy startup-config
tftp:backup.cfg.
A backup configuration from a TFTP server cannot be copied
directly into the startup-config.
The command copy running-config startup-config should
be used to save the changes on the switch.
Downloading to the startup-config requires the switch to be
reloaded in order for the configuration to take effect.
17. What two methods can be used to remove MAC address table
entries from a switch? (Choose two.)
Power cycle the switch to clear all dynamically learned
addresses.
The clear switching-tables command will
remove statically configured entries.
The clear mac-address-table command will
remove statically and dynamically configured table entries.
The erase flash command will clear all
statically configured table entries.
Statically configured MAC addresses will automatically be
removed from the address table 300 minutes after the last activity on a switch
port.
18. Which type of traffic can still be received on a switch
interface that is in STP blocking mode?
BPDU frames
multicast frames
broadcast frames
Layer 3 packets
19. Which method establishes an administrative connection for
configuring the Linksys WRT300N wireless access point?
Associate with the access point and then open a HyperTerminal session
with the access point.
Physically connect to the access point and then reboot the
computer to launch the configuration software.
From a computer in the same IP subnet as the access point,
enter the default IP address of the access point in a web browser.
Modify the TCP/IP properties of the computer connected to
the access point so that it exists on the same network, and then reboot your
computer to establish a connection.
20.Refer to the exhibit. All edge ports are configured with
the spanning-tree portfast command. Host1 is recently connected
to port Fa0/1 on switch SW1 . Which statement is true about the status of port
Fa0/1?
The port will transition into blocking state.
The port will transition immediately into forwarding state.
The port will transition into blocking state and then immediately
into forwarding state.
The port will transition into blocking state and
immediately transition through the listening and learning states.
21.Refer to the exhibit. What is true of the configuration of
switch S1?
A Cisco proprietary protocol is in use for ports Fa0/1 and
Fa0/3.
Switch ports Fa0/1 and Fa0/3 have been configured with the switchport
mode access command.
Untagged frames received on ports Fa0/1 and Fa0/3 will be
placed on VLAN 1.
Switch ports Fa0/1 and Fa0/3 are configured to carry data
from multiple VLANs.
22.Refer to the exhibit. The configuration steps that are
listed in the exhibit have been entered in switch S1 via the console.
Subsequent attempts to telnet to the switch are not successful. What is causing
the problem?
The switch must be configured with SSH version 1.
The transport input command must specify
Telnet access.
The RSA keys must be returned to zero before SSH will
permit Telnet access.
The ip domain-name command must also be
entered in line configuration mode for the vty lines.
23.Refer to the exhibit. Which switch will be elected as the
root bridge of the spanning tree topology?
Cat-A
Cat-B
Cat-C
Cat-D
24.Refer to the exhibit. VTP has been configured with VTP
pruning enabled on all switches. If HostA sends a broadcast frame to SW1, which
devices will receive the frame?
SW1, SW3, HostF
SW1, HostB, HostC
SW1, SW2, SW3, SW4, HostF
SW1, SW2, SW3, SW4, all hosts
25.
Refer to the exhibit. Which two statements are true about the operation of the interfaces? (Choose two.)
Incoming traffic with VLAN ID 0 is processed by interface
fa0/0.
Incoming traffic that has a VLAN ID of 2 is processed by
subinterface fa0/0.2.
Both subinterfaces remain up with line protocol up, even if
fa0/0 line protocol is down.
Subinterfaces use unique MAC addresses by adding the 802.1Q
VLAN ID to the hardware address.
Traffic inbound on this router is processed by different
subinterfaces, depending on the VLAN from which the traffic originated.
26. The network administrator wants to configure a switch to
pass VLAN update information to other switches in the domain but not update its
own local VLAN database. Which two steps should the administrator perform to
achieve this? (Choose two.)
Reset the VTP counters.
Configure VTP version 1 on the switch.
Configure the VTP mode of the switch to transparent.
Verify that the switch has a higher configuration revision
number.
Configure the switch with the same VTP domain name as other
switches in the network.
27.Refer to the exhibit. The devices in the network are
operational and configured as indicated in the exhibit. However, hosts B and D
cannot ping each other. What is the most likely cause of this problem?
The link between the switches is up but not trunked.
The Fa0/11 interface of Switch1 is not configured as a
trunk.
Hosts B and D are configured with IP addresses from
different subnets.
VLAN 20 and VLAN 30 are not allowed on the trunk between
the switches.
28.Refer to the exhibit. Users A and B are reporting
intermittent connectivity problems. Pre-installation surveys showed strong
signal strength from the AP locations to the client locations. Outside
electrical interference has been eliminated. What will fix the problem?
Relocate the APs closer to each other.
Increase the distance between the clients.
Change the channel on AP-B to 6 or 11.
Place AP-A and AP-B on the same wireless channel.
29. Why is it advisable that a network administrator use SSH
instead of Telnet when managing switches?
SSH uses TCP whereas Telnet does not.
SSH encrypts only the username and password when logging
in.
SSH encrypts all remote management communications whereas
Telnet does not.
SSH sends a clear text message steam which reduces the
bandwidth use for management.
30.Refer to the exhibit. The teacher host is connected to
port Fa0/7 on switch STW. A student has decided to share access to the Internet
by attaching a hub and laptop to STW as shown. What will be the result of the
student making this connection?
The Fa0/7 port of STW will be shutdown.
The student will gain full access to the Internet.
Both the teacher and student will be able to receive data
but only the teacher will be able to send.
The frames from the laptop will be dropped, but the teacher
host will maintain connectivity with the network.
31. A network administrator configures a switch port with the
commandswitchport mode dynamic auto. What is the resulting behavior of
the switch port?
The switch port is able to trunk if the remote switch port
is set to auto.
The switch port is able to trunk if the remote switch port
is set to desirable.
The switch port will be disabled if it is unable to
successfully negotiate trunking.
A successful trunk will be established if the remote switch
is non-Cisco but the port is configured for trunking.
32. Which STP port type can only appear once on a segment,
and must be present in order for traffic to flow on that segment?
non-root port
disabled port
designated port
non-designated port
33.Refer to the exhibit. What would happen if the network
administrator moved the network cable of Host A from interface Fa0/1 to Fa0/3
on switch SW1?
Host A remains a member of VLAN 10, because the router is
routing traffic between VLANs.
Host A is no longer a member of VLAN 10, because port Fa0/3
has been manually assigned to VLAN 30.
Host A remains a member of VLAN 10, because the switch
provides dynamic VLAN assignment for the port.
Host A maintains connectivity to all members of VLAN 10,
because it is connected to the same physical network.
Host A is no longer a member of VLAN 10, but because port
Fa0/3 was unused, it is now a member of VLAN 1.
34.Refer to the exhibit. VLAN 10 has been configured on the
VTP server. Users who are assigned to VLAN 10 are connected as shown in the
exhibit. On the basis of the outputs that are provided, which group of users
will be able to communicate with the users on VLAN 10 on SW1?
all the users who are connected only to SW2
users on VLAN 10 who are connected only to SW3
users on VLAN 10 who are connected only to SW4
users on VLAN 10 who are connected to both SW3 and SW4
35. Refer to the exhibit. Which three options correctly
identify information that could be associated with this output?(Choose three.)
Interface FastEthernet3/0/0 is subinterfaced.
A non-proprietary trunking protocol is in use.
The configuration is appropriate for a router-on-a-stick
network design.
A shutdown command has been applied to
interface FastEthernet3/0/0.
Interface FastEthernet3/0/0.3 is mapped to the default
management VLAN.
An IP address should be applied to FastEthernet3/0/0 for
correct data routing.
36. Refer to the exhibit. The Layer 2 switching design that
is shown has been implemented in a campus environment that is using Spanning
Tree Protocol. All inter-switch links that are shown are trunks. Whenever an
inter-switch link fails, the network takes nearly a minute to completely
converge. How can the convergence time be reduced?
Increase the capacity of the distribution and core trunk
links to 10 Gb/s.
Add a trunk link that directly connects D1 and D2.
Use Layer 3 switching on the core switch.
Implement Rapid Spanning Tree Protocol.
37. Refer to the exhibit. Each switch is configured to
participate in STP for VLANs 1, 10, 20, and 30. Which switch will become the
root for VLAN 20?
A
B
C
D
38. Refer to the exhibit. Switches S2 and S3 are properly
connected using an ethernet cable. A network administrator has configured both
switches with VTP, but S3 is unable to propagate VLANs to S2. What could be the
reason for this?
The VTP configuration revision is different on both
switches.
The VTP domains are different on both switches.
VTP pruning is disabled.
VTP v2 is disabled.
39. In a three-layer hierarchical network design, which
distribution layer function delineates broadcast domains?
routing between VLANs
aggregating traffic flows
providing redundant links
reducing the network diameter
40. Which parameter is used to uniquely identify one wireless
network from another?
SSID
OFDM
WEP
DSSS
41. What is one disadvantage that 802.11a wireless has
compared to 802.11g?
Use of the 5GHz band requires much larger antennas.
The OFDM modulation technique results in a slower data
rate.
There are fewer non-overlapping channels available to help
reduce RF interference.
The use of higher frequencies means that signals are more
likely to be obstructed.
42. Which three statements are correct concerning the default
configuration of a new switch? (Choose three.)
It is configured in VTP server mode.
STP is automatically enabled.
The first VTY line is automatically configured to allow
remote connections.
VLAN1 is configured with a management IP address.
All switch ports are assigned to VLAN1.
The enable password is configured as cisco.
43. Refer to the exhibit. How is port Gi1/1 on SWT-A
functioning in the spanning-tree topology?
It is sending and receiving data frames.
It is receiving BPDUs, but not sending data frames.
It is participating in the election process by forwarding
the BPDUs it receives.
It is receiving BPDUs and populating the MAC address table,
but not sending data.
44. While configuring a new switch, a network administrator
configures the switch as an HTTP server. What benefits does this configuration
provide?
This allows the switch to host web pages for the network.
This allows remote VPN connections to the switch over the
Internet.
This is required if a web server or web farm is attached to
the switch.
This allows web-based configuration tools to be used with
the switch.
45. Which statement describes the use of voice VLANs in Cisco
IP telephony?
The voice VLAN carries both tagged and untagged traffic.
The voice VLAN carries untagged traffic having special QoS
markings.
The voice VLAN must be configured on the switch port to
which the IP phone attaches.
Data and voice frames are tagged with same VLAN ID between
the IP phone and the switch when a voice VLAN is configured.
46. Refer to the exhibit. If switch SW1 is configured with
the four VLANs as shown in the exhibit, how many physical interfaces are needed
on router R1 to configure inter-VLAN routing using subinterfaces?
zero
one
two
four
47. Refer to the exhibit. What does the term DYNAMIC indicate
in the output that is shown?
This entry can only be removed from the MAC address table
by a network administrator.
When forwarding a frame to the device with address
0060.5c5b.cd23, the switch does not have to perform a lookup to determine the
final destination port.
Only the device with MAC address 0060.5c5b.cd23 will be
allowed to connect to port Fa0/18.
The switch learned this MAC address from the source address
in a frame received on Fa0/18.
48. Refer to the exhibit. The VTP domain has been configured
as shown in the exhibit. The network technician accidentally configured the VTP
server as a VTP client. After the technician reloaded the switches, all users
in the VTP domain started to complain that they lost connectivity to the users
on the same VLANs that are connected to other switches. What should be done in
the future to prevent losing all VLAN configurations in a VTP domain?
Configure all switches in VTP transparent mode and copy the
VLAN configuration into flash.
Configure all switches in the network as VTP clients and
copy the VLAN configuration into NVRAM.
Create a new domain and configure a second switch as a VTP
server to take over in case of a primary VTP server failure.
In the same domain, configure a second switch as a VTP
server to take over in case of a primary VTP server failure.
49. Refer to the exhibit. How does SW1 manage traffic coming
from Host A?
SW1 drops the traffic because it is untagged.
SW1 leaves the traffic untagged and forwards it over the
trunk.
SW1 tags the traffic with the lowest VLAN ID value and
forwards it over the trunk link.
SW1 encapsulates the traffic with 802.1Q encapsulation and
forwards it over the trunk link.
50. An administrator is troubleshooting a PC on the network
which is suffering from slow and intermittent connectivity. The PC has a ping
success rate to the default gateway of less than half the ping attempts. Other
PCs on the switch can consistently ping the default gateway. The switch port is
configured for auto duplex and the PC is configured for full duplex. What will
commonly cause this problem?
The PC is set to full duplex. The switch port fails to
autonegotiate the duplex setting and defaults to half duplex, which causes a
duplex mismatch.
The switch traffic is exceeding available frame buffers.
The result is that frames are being dropped.
The PC and the default gateway have different bandwidth
Ethernet ports.
The default gateway is not on the same switch that the PC
is.
51. Refer to the exhibit. A network administrator has
segmented the network into two VLANs and configured Router1 for inter-VLAN
routing. A test of the network, however, shows that hosts on each VLAN can only
access local resources and not resources on the other VLAN. What is the most
likely cause of this problem?
Switch port Fa0/1 is not trunking.
Router interface Fa0/0 is possibly down.
No routing protocol is configured on Router1.
One of the router subinterfaces is possibly down.
52. What impact does the use of the mdix
auto configuration command have on an Ethernet interface on a switch?
automatically detects duplex settings
automatically detects interface speed
automatically detects copper cable type
automatically assigns the first detected MAC address to an
interface
No comments:
Post a Comment